SEND AN EMAIL

Home> Products> >SATADIMM SSD

SATADIMM™ Solid State Drive

SATADIMM™ is the first and only enterprise class SSD to be designed in a DIMM form factor making it possible to deploy SSDs in unused DRAM sockets.

Best Fit Applications

SATADIMM is the ideal boot drive for high-performance servers and storage appliances delivering just the right capacity without sacrificing drive bays that are better suited for mass storage. SATADIMM’s optimized performance and endurance makes it perfect as a cache solution to accelerate applications, especially VMware. In a storage array appliance, SATADIMM provides a 5x advantage in performance and capacity over using 2.5-inch SSDs.

Mitigate Human Error

Booting and caching are just two applications where the removability of a hard drive form factor can be problematical. Imagine the ramifications of a degraded or downed system resulting from an operator removing the boot or cache drive by mistake. The ultra-reliable SATADIMM is safely stored away inside the server ensuring this sort of catastrophe is easily avoidable.

Unsurpassed Server Capacity & Performance

Form is Function: this high-performance and high-availability SSD offers significant increases to typical server capacity and performance at a fraction of the volumetric density of a 2.5-inch SSD. It’s a simple advantage: a server with SATADIMM will have greater capacity and performance than a server with storage only in drive bays.

Features

  • Capacities up to 480GB
  • Best in class SATA III (6Gb) sequential and random performance
  • No data loss upon power failure
  • MLC and SLC NAND flash supported
  • Data compression for industry-leading endurance
  • Protection against catastrophic flash sector/page/block failures
Capacity
SLC Up to 400GB
MLC / eMLC Up to 480GB 
Performance
Sustained Read / Write 520 MB/s
Sustained Random Read & Write IOPS Up to 60,000 IOPS
Interface SATA 6Gb
Reliability
ECC 55bit / 512 BCH
Bit Error Rate (BER) <1 in 1017 bits read
Power Fail Data Protection Yes
Endurance *5 Years +
Tiered Error Protection Data recovery from sector, page, and block failure. End-to-End CRC protection
Temperature Monitoring On-board sensor, S.M.A.R.T. Attribute
Environmental
Shock 50g, 11ms, 3 shocks applied in each direction on 3 mutually perpendicular axis
Vibration 16.4g rms 10 - 2,000 Hz, 3 axis
Operating Temperature -40°C to 85°C
Non-operating Temperature -40°C to 85°C
Altitude 80,000 feet
Humidity 5% to 95%, non-condensing, relative
Safety / Agency / Compliance FCC, CE, TUV
Power
Power Voltage 1.5V - 3.3V +5%
Active <6.0 Watts
Idle 0.9 Watts
Dimensions
Form Factor JEDEC MO-269F
Length 133.35mm (length) x <30.00mm*** (height) x 6.75mm (thick)
SATA Connectivity **Standard SATA Connector
SATADIMM Scalability Advantages
Existing deployed servers Can enable SSD performance without sacrificing HDD drive bays
  Can scale depending on available DDR3 DIMM sockets
  Price and performance can scale over time
  Does not occupy precious PCIe slots, which are best suited to HBA's
  Can optimize servers for fast boot solution
  Very low power consumption compared to HDD & PCIe SSDs 
  Upgrades existing servers without disrupting current storage
*Performance throttling may be engaged to ensure 5-year endurance.
** Option to route SATA signals through DIMM edge connector is available.
*** Ask your Viking sales representative about special SATADIMM options for 1U servers

 

Specification Sheet

Email to a Friend

Specification
Infographic & Comparison Charts  Contact and Support

Specification Sheet

Specification

Contact and Support